Water Heaters

American Standard Series Gas Standard Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Available in 30, 40 & 50 Gallon capacities in
Short & Tall configurations

Features:

  • COMPLIES WITH NAECA REQUIREMENTS— effective April 16, 2015, and Federal Energy Conservation Standards, in accordance with the Energy Policy and Conversation Act, (EPCA), as amended
  • VAPORSHIELD TECHNOLOGY— Shuts off gas and air supply to heater to prevent prolonged vapor burn in combustion chamber should accidental or unattended ignition of flammable vapors occur outside the water heater.
  • SPARK IGNITER— Affords push button pilot lighting in lieu of matches.
  • MAINTENANCE FREE — No periodic cleaning of combustion air inlet necessary under normal conditions.
  • SELF-CLEANING— Turbulence inducing cold water inlet-tube engineered to diminish hard water area sediment deposits.
  • NON-CFC FOAM INSULATED — Saves energy and reduces fuel costs by maximizing heat retention.
  • HEAVY GAUGE STEEL TANK — For extra years of trouble-free service.
  • GLASS-LINED TANK — Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum protection from the effects of corrosion.
  • ALUMINUM ANODE ROD— To protect tank life.
  • FACTORY INSTALLED DIELECTRIC HOT & COLD WATER CONNECTIONS — ¾” NPT water connections to extend tank life and for easier installations.
  • BRASS DRAIN VALVE — ( Full Port Ball)- Designed to allow easy draining and avoid clogging.
  • FACTORY INSTALLED HEAT TRAPS — Reduces standby heat loss in water piping.
  • TEMPERATURE & PRESSURE RELIEF VALVE— Factory provided T & P Valve can be relocated from side to optional top opening.
  • FACTORY INSTALLED ENERGY CUT-OFF SYSTEM — Automatic thermostat with built-in gas pressure regulation also incorporates energy cut-off switch to prevent abnormally high water temperature for added safety.
  • DESIGN CERTIFIED BY CSA INTERNATIONAL— To meet or exceed ANSI requirements.  Tested in accordance with D.O.E. procedures and meets or exceeds the energy efficiency requirements of ASHRAE and all state energy efficiency standards.
  • CHOICE OF 6 OR 12 YEAR LIMITED TANK WARRANTY — Includes 6 or 12 Year Limited Warranty on Component Parts.

American Standard Series Gas Standard Vent
Tall

GSN40T1-3-6 40 gallon 6 year warranty – $1395.00

GSN40T1-3-12 40 gallon 12 year warranty – $1725.00

GSN50T1-3-6 50 gallon 6 year warranty – $1595.00

GSN50T1-3-12 50 gallon 12 year warranty – $1985.00

Short

GSN40L2-3-6 40 gallon 6 year warranty – $1395.00

GSN40L2-3-12 40 gallon 12 year warranty – $1725.00

GSN50L2-3-6 50 gallon 6 year warranty – $1675.00

GSN50L2-3-12 50 gallon 12 year warranty – $2025.00
Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.

American Standard Series Gas Standard Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Available in 75 Gallon & 100 Gallon
Residential Duty Commercial-Storage Gas

Features:

  • HEAVY GAUGE STEEL TANK – for extra years of trouble-free service.
  • INNER TANK GLASS-LINED – with Dura-Glas™and fired at 1600° F for optimum protection from the effects of corrosion.
  • R-16 NON-CFC FOAM INSULATED – to save energy and reduce fuel costs by maximizing heat retention.
  • HEAVY DUTY ANODE ROD – to prolong tank life.
  • FURNISHED WITH THREE OR FOUR HEAVY GAUGE STEEL LEGS RESPECTIVELY – to ensure durability & rock-steady installation (G75-T2 AS – 3 legs & G100-T2 AS – 4 legs).
  • AUTOMATIC NON-ELECTRIC GAS THERMOSTAT ADJUSTABLE TO 160° F – When installed with a mixing valve, these water heaters can deliver 160° F sanitizing & 140° F general purpose hot water simultaneously.
  • COMBUSTION CHAMBER DOOR – including bolted exterior outside access & sliding inner door to sequester burner & pilot area for added safety.
  • FACTORY INSTALLED ENERGY CUT-OFF SYSTEM & PRESSURE/TEMPERATURE RELIEF VALVE.
  • SMALL VENT SIZE & TOP MOUNT 1″ OR 1 1/4” WATER CONNECTIONS RESPECTIVELY – ensures universal replacement of all other brands. (G75-T2 AS = 1″ & G100-T2 AS = 1 ¼”).
  • AMERICAN STANDARD GAS WATER HEATERS & FOR 150 PSI WORKING PRESSURE.– are certified at 300 PSI test pressure & for 150 PSI working pressure.
  • ALL TANKS ARE HYDROSTATICALLY TESTED AT THE FACTORY.
  • TESTED & ETL LISTED WITH INTERTEK – in accordance with ANSIZ21.10.3 as an automatic storage and/or automatic circulating tank heater. ASHRAE Standard 90.1 1999 addendum 90.1b. ETL Listed to meet NSF/ANSI 5 Standards.
  • CHOICE OF SIX OR TWELVE YEARS LIMITED TANK WARRANTY – Includes 6 or 12 Years Limited Warranty on Component Parts.

American Standard Series Gas Standard Vent
Tall

G-75T2 AS 75 gallon 6 year warranty – $2295.00

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.

American Standard Series Gas Power Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Available in gallon capacities of 40 and 50 Tall & 50 Short
configurations – Natural or LP Gas

Features:

  • ENERGY STAR® QUALIFIED — All models qualify for the April 16, 2015
    minimum ENERGY STAR® UEF requirement and may also qualify for local utility and rebate programs.
  • FACTORY INSTALLED HEAT TRAPS — Reduces standby heat loss in water piping.
  • HFO FOAM INSULATED — 2-inch thick, “Environmentally-Friendly” insulation foam saves energy, reduces fuel costs by maximizing heat retention, and contributes to overall energy efficiency.
  • INTELLIGENT GAS CONTROL — With a hot surface pilot ignition system. This results in savings of pilot gas during standby periods (120 V.A.C.). A Microprocessor constantly monitors and controls burner operation to maintain consistent and accurate water temperature levels.  LED control light displays operation status and diagnostics information to assist the installer in troubleshooting.  Built-in gas pressure regulation also incorporates energy cut-off switch to prevent
    abnormally high water temperature for added safety
  • FLAMMABLE VAPOR SENSOR — The electronic sensor connected to an electric switch prevents burner operation if flammable vapors are detected. The sensor and electric switch will also prevent operation if there is ongoing flammable vapor burn inside the combustion chamber. RESPECTIVELY – to ensure durability & rock-steady installation (G75-T2 AS – 3 legs & G100-T2 AS – 4 legs).
  • VAPORSHIELD TECHNOLOGY — Shuts off gas to the heater and stops the blower to prevent prolonged vapor burn in the combustion chamber should accidental or unattended ignition of flammable vapors occur outside the water heater.
  • HEAVY GAUGE STEEL TANK — For extra years of trouble-free service.
  • GLASS-LINED TANK — Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum protection from the effects of corrosion.
  • ALUMINUM ANODE ROD — To protect tank life
  • BRASS DRAIN VALVE — (Full Port Ball)- Designed to allow easy draining and avoid clogging.
  • TEMPERATURE & PRESSURE RELIEF VALVE — Factory provided T & P Valve can be relocated from side to optional top opening.
  • MAINTENANCE FREE — No periodic cleaning of combustion air inlet necessary under normal conditions.
  • SELF-CLEANING — Turbulence inducing cold water inlet-tube engineered to diminish hard water area sediment deposits.
  • FACTORY INSTALLED HOT & COLD WATER CONNECTIONS — ¾” NPT water connections for extended tank life and easier installation.
  • POWER VENTED WATER HEATER — Designed for installations where atmospheric units cannot be used. Exhaust gases are vented under positive pressure directly out of the building through the roof or the wall.
  • SIGHT GLASS WINDOW — Offers a view into the combustion chamber to observe the operation of the igniter and burner
  • DESIGN-CERTIFIED BY CSA INTERNATIONAL — Certified at 150 PSI working pressure & Certified to ANSI Z21.10.1 standards governing storage tank-type water heaters.
  • CHOICE OF SIX OR TWELVE YEARS LIMITED TANK WARRANTY – Includes 6 or 12 Years Limited Warranty on Component Parts.

American Standard Series Gas Power Vent
Tall

PV40TLN-6 40 gallon 6 year warranty – $2085.00

PV40TLN-12 40 gallon 12 year warranty – $2545.00

PV50TLN-6 50 gallon 6 year warranty – $2185.00

PV50TLN-12 50 gallon 12 year warranty – $2645.00

Short

PV50SLN-6 50 gallon 6 year warranty – $2245.00

PV50SLN-12 50 gallon 12 year warranty – $2695.00

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.

Rheem Professional Classic Series Gas Standard Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic Plus™ Atmospheric gas water heaters are engineered for more hot water at a low operating cost

  • .58 – .66 UEF
  • Eco-friendly burner, low NOx design
  • 29, 30, 40 and 50 gallon capacities

Features:

Efficiency

  • .58 – .66 UEF
  • More hot water at a low operating cost

Performance

  • FHR: 51 – 87 gallons
  • Recovery: 30.3 to 40.4 GPH at a 90° F rise, depending on model

Guardian System™ & Sensor

  • Exclusive air/fuel shut-off device
  • Maintenance free – no filter to clean
  • Protective control system that disables the heater in the presence of flammable vapor accumulation

Low Emissions

  • Eco-friendly burner, low NOx design
  • Meets 40 ng/J NOx requirements

Longer Life

  • Premium grade anode rod provides long-lasting tank protection

Plus…

  • Easy to light – no matches required
  • EverKleen™ patented system fights sediment build-up
  • Enhanced flow brass drain valve
  • Temperature and pressure relief valve included
  • Low lead compliant
  • Standard replacement parts
  • Includes a 6 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Classic Series Gas Standard Vent
Tall

PROG29-32N RH63 29 gallon – $

PROG40-38N RH62 40 gallon – $1545.00

PROG50-38N RH62 50 gallon – $1725.00
Short
PROG40S-38N RH62 40 gallon – $1545.00

PROG50S-40N RH62 50 gallon – $2045.00
Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.


Rheem Professional Classic Plus Series Gas Standard Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic Plus® Atmospheric gas water heaters are engineered for more hot water at a low operating cost

  • .58 – 66 UEF
  • Eco-friendly burner, low NOx design
  • 40, 48, 50 and 55 gallon capacities

Features:

Efficiency

  •  .58 – .66 UEF
  • More hot water at a low operating cost

Performance

  •  FHR: 52 – 105 gallons
  • Recovery: 36.4 to 61 GPH at a 90° F rise, depending on model

Guardian System™ & Sensor

  •  Exclusive air/fuel shut-off device
  • Maintenance free – no filter to clean
  • Protective control system that disables the heater in the presence of flammable vapor accumulation

Low Emissions

  • Eco-friendly burner, low NOx design
  •  Meets 40 ng/J NOx requirements

Longer Life

  •  Premium grade anode rod provides long-lasting tank protection

Plus…

  •  Easy to light – no matches required
  • EverKleen™ patented system fights sediment build-up
  •  Enhanced flow brass drain valve
  • Temperature and pressure relief valve included
  • Low lead compliant
  • Standard replacement parts
  • Includes 8 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Series Gas Heavy Duty Standard Vent
Tall
PRO+G40-40N RH62 40 gallon – $1645.00

PRO+G50-40N RH62 50 gallon – $1745.00

Short

PRO+G40S-40N RH62 40 gallon – $1745.00
Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.


Rheem Professional Classic Plus Heavy Duty Gas Standard Vent

 Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic Plus® Heavy Duty gas water heaters exceed ANSI standards for flammable vapor ignition resistance

  • Guardian System™ & sensor
  • Low emission
  • No matches required
  • 75- 98 gallon capacities

Features:

Performance

  •  Recovery Capacity: 72.8 gallons per hour (delivers approximately 100 gallons of hot water in the first hour for 75-gallon models and 142 gallons for 98-gallon models)**

Guardian System™ & Sensor

  •  Exclusive air/fuel shut-off device
  • Maintenance free – no filter to clean
  •  Disables the heater in the presence of flammable vapor accumulation

Easy to Light

  •  Piezo Ignitor – no matches required

Low Emissions

  •  Eco-friendly burner, low NOx design
  •  Meets 40 ng/J NOx requirements

Longer Life

  •  Premium grade anode rod provides long-lasting tank protection

Plus…

  •  Enhanced-flow brass drain valve
  •  Temperature and pressure relief valve included
  • Low lead compliant
  •  Side water connections for space heating applications
  • Standard replacement part
  • Includes 8 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Classic Plus Heavy Duty Gas Standard Vent

Tall

PROG+G75-76N RH 75 gallon – $2595.00

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.


Rheem Professional Classic Gas Power Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic™ Power Vent gas water heaters offer up to 100 foot vent runs, energy efficiency and the Guardian System

  • Induced draft with the Guardian FVIR System
  • Flexible venting options up to 100 feet
  • 40 and 50 gallon tall and short capacities
  • Integrated self-diagnostic system control, thermostat and gas valve
  • SCAQMD rule 1121 compliant models available: 10ng/J NOx emission

Features:

Efficiency

  • .61 – .69 UEF

Performance

  • FHR: 67 – 84 gallons
  • Recovery: 32.4 to 42.4 GPH at a 90° F rise

Self-Diagnostic System

  • Electronic gas control for improved monitoring> and service

Low Emissions

  • Eco-friendly burner, low NOx design

Features

  • Uses indoor air for combustion; blower> exhausts the flue gases
  • Standard 120 VAC electrical connection
  • New whisper quiet blower

Guardian System™ & Sensor

  • Exclusive air/fuel shut-off device
  • Maintenance free – no filter to clean
  • Disables the heater in the presence of flammable vapor accumulation

Flexible Venting Options

  • Long venting lengths up to 100 equivalent feet
  • PVC, ABS, or CPVC vent pipe options
  • Vertical or horizontal termination

Longer Life

  • Rheem exclusive R-Tech (resistored) anode rod> provides long-lasting tank protection

High Altitude Compliant

  • Tall models certified for applications up to 7,800 ft. above sea level and short models up to 6,000 feet above sea level

Plus…

  • Enhanced-flow brass drain valve
  • Temperature and pressure relief valve included
  • Low lead compliant
  • Durable Silicon Nitride Ignitor (HSI)
  • EverKleen™ patented system fights sediment build-up
  • Standard replacement parts
  • Includes 6 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Classic Gas Power Vent

Tall

PROG40-40N RH67 PV 40 gallon – $

PROG50-42N RH67 PV 50 gallon – $

Short

PROG40S-36N RH67 PC 40 gallon – $2185.00

PROG50S-36N RH67 PC 50 gallon – $

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.


Rheem Professional Classic Plus Heavy Duty Gas Power Vent

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic Plus® Heavy Duty Power Vent gas water heater offers a larger capacity, a flexible venting option and the Guardian System

  • Standard 110 VAC electrical connection
  • New whisper quiet blower
  • 75 gallon tall and short capacities

Features:

Performance

  •  Recovery Capacity: 72.8 gallons per hour (delivers approximately 110 gallons of hot water in the first hour)**

Self-Diagnostic System

  •  Electronic gas control for improved monitoring and service

Low Emissions

  •  Eco-friendly burner, low NOx design

Features

  •  Uses indoor air for combustion; blower exhausts the flue gases
  •  Standard 110 VAC electrical connection
  •  New whisper quiet blower
  •  Offers larger capacities than the standard Power Vent

Guardian System™ & Sensor

  •  Exclusive air/fuel shut-off device
  •  Maintenance free – no filter to clean
  •  Disables the heater in the presence of flammable vapor accumulation

Flexible Venting Options

  •  Long venting lengths up to 100 equivalent feet
  •  PVC, ABS, or CPVC vent pipe options
  •  Vertical or horizontal termination

Longer Life

  •  Premium grade anode rod provides long-lasting tank protection

Plus…

  •  Enhanced flow brass drain valve
  •  Temperature and pressure relief valve included
  •  Low lead compliant
  •  Durable silicon nitride ignitor (HSI)
  •  EverKleen™ patented system fights sediment build-up
  •  Standard replacement parts
  • Includes 8 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Classic Plus Heavy Duty Gas Power Vent

PRO+G75-76N RH PV 75 gallon – $3450.00

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.


Rheem Professional Electric Classic Standard

Installed price: Please see pricing below
Installed price includes normal installation. Upgrades, difficult access, irregularities, code compliance may be extra.
City Permits are required by most cities for gas water heaters and are an additional charge per your City permit rates.

Professional Classic™ electric water heaters are engineered for longer life – resistored heating elements and premium grade anode rod

  • .90 – .93 UEF
  • Enhanced-flow brass drain valve
  • 19.9 to 55 gallon capacities

Features:

Efficiency

  •  .90 – .93 UEF
  • Isolated tank design reduces conductive heat loss
  • Resistored copper upper element and resistored Lifeguard™ stainless steel lower element to prolong anode rod and tank life

Performance

  •  FHR: 45 – 67 gallons, based on gallon capacity
  • Recovery: 21 GPH at a 90° F rise

System Sentinel (Available on selected models)

  •  Exclusive diagnostic system with glowing LEDs that verify heating element operation. LEDs pin point the exact location of functioning or non-functioning heating elements

Longer Life

  •  Premium grade anode rod provides long-lasting tank protection

Features

  •  Electric junction box located above heating elements for easy installation
  • Over-temperature protector cuts off power in excess temperature situations
  • Automatic thermostat keeps water at desired temperature

Plus…

  •  EverKleen™ self cleaning device fights harmful sediment build-up with a high-velocity spiraling water stream – helps operating efficiency by saving energy, money and improving tank life
  • Enhanced-flow brass drain valve
  • Temperature and pressure relief valve included
  • Low lead compliant
  • Includes 6 year tank & parts warranty
  • Optional 4 year extended warranty – contact office for pricing

Professional Electric Classic Standard

Tall

PROE30 T2 RH95 30 gallon – $1045.00

PROE40 M2 RH95 40 gallon – $1045.00

PROE50 T2 RH95 50 gallon – $1085.00

Short

PROE36 S2 RH95 36 gallon – $1225.00

Download Spec Sheet

FOR THE MOST CURRENT PRICING PLEASE CALL, ALL PRICING SUBJECT TO JOBSITE VISIT.